Teledu 4Pcs For B2500 B3000 Ranger Front Upper Ball Joints Control Arms Suspension

14.Measure the chassis and adjust if necessary15.Check and, if necessary, adjust the headlight settings on vehicles with automatic headlight leveling where the leveling sensor is attached to the control arm16.To conclude, test-drive the vehicleBall JointBall Joint Replacement Guideline:If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspensionThe side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty1.Raise the vehicle and remove the front wheels2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts4.Loosen and remove the fixing nut of the ball joint on the steering knuckleTip:If the ball stud rotates, hold the ball stud in place with a hexagon socket5.Remove the bad or worn ball joint from the control arm6.Loosen the compression ball joint on the steering knuckle using a suitable special tool7.Clean the cone connectionTip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary11.Finally, carry out a test driveFrequently Asked Questions(1).What\'s the function of control arm?The control arm connects the hub and the frame of the car. There are ball joints on the hub side and bushings on the frame side to achieve up and down instead of forward and rearward(2).What is the significance of the control arm for the car?(3).How to tell the quality of control arm?Look at the materials and processing of the control arm: the materials used to control the arm, common are steel and aluminum alloy. In ordinary family cars, steel control arms are very common, and the basic appeal is to meet the strength while controlling costs. In the middle and high-end models, you will see the control arm of the aluminum alloy and the wheel bearing housing. In addition to meeting the strength of the suspension, this material can further reduce the weight and reduce the weight of the suspension spring to improve the suspension response. Improve driving performance.(4).Do I need to replace the control arm if the bushings are worn? What is the safety risk?(5).What is the average cost of replacing control arms?The cost to replace control arms depend on the vehicle. Control arms cost different amounts depending on the vehicle, as well as the labor to install. Some are easy to install and take little time, while others can take several hours(6).How will I know that I have to renew my ball joint parts? Or replace them?If your ball joint fails, you will listen to a strange sound while driving. And that sound may help you to realize that your ball joint has failed and you have to renew them(7).What happens if a ball joint breaks?When a ball joint breaks, you will hear a mysterious noise inside your car wheelYour car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control Brand: Unbrand Manufacturer Part Number: E80204502CP Interchange Part Number: K80052,K80054,K8738,1F6134211,1F6135211,F87A3084AA Placement on Vehicle: Front, Left, Right, Upper Surface Finish: Premium Quality Greasable or Sealed: Greasable Suspension Grade: Standard Superseded Part Number: Front Driver and Passenger Side Replacement Custom Bundle: Yes Bundle Description: Ball Joint,Control Arm and Ball Joint Assembly Type: Control Arm & Ball Joint Assembly Items Included: Mounting Hardware Features: Greasable OE/OEM Part Number: Suspension Control Arms and Ball Joints Assembly Material: Alloy Steel Manufacturer Warranty: 10 Year Mounting Style: Bolt-On Universal Fitment: No Cotter Pin Hole: Yes Control Arm Construction: Forged