Teledu For 05-06 Equinox 06 Torrent 02-07 Vue 12pc Front Wheel Bearings & Hub+TieRods

Tip:Secure the ball stud against twisting with a suitable tool9.Insert new stabilizer link at stabilizer10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturerTip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension12.Conclude with a test driveTie-Rod End Replacement Guideline:This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rodNote: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance1.Lift the vehicle and dismount the front axle wheels2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes3.Dismount the front underride guard4.Loosen the fastening nut from the tie rod and remove it completely5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator6.Remove the clamp of the bellow on the steering gear7.Push the bellow towards the tie rod end8.Unscrew the inner tie rod from the rack9.Clean the sealing face of the bellow at the steering gear10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckleNote:Always use new self-locking nuts and bolts for a reliable repair11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer12.Mount the bellow and close the clamps with the appropriate special toolNote:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturerNote:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure 14.Mount the front underride guard15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications17.Perform a test driveFrequently Asked Questions(1).Do I need to replace the control arm if the bushings are worn?(2).What happens if a ball joint breaks?When a ball joint breaks, you will hear a mysterious noise inside your car wheelYour car tire will wear-out since your alignment will be broken, and you will feel the car getting out of controlIf the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be seriousBroken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car(3).What happens if I don\'t replace ball joints?(4).Do I need to grease new ball joints?I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new 1 after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card Brand: Unbrand Manufacturer Part Number: E82422710CP Interchange Part Number: K5331 K80461 K80460 K80850 ES800030 EV80781 513189 Surface Finish: Polished, Rust Protected Placement on Vehicle: Left, Right, Front, Rear, Lower Superseded Part Number: Front Rear Driver and Passenger Side Replacements Custom Bundle: Yes Bundle Description: Suspension Steering Tie Rod Ends Linkages Assembly Modified Item: Yes Type: Wheel Hub & Bearing Assembly Items Included: Mounting Hardware Manufacturer Warranty: 10 Year Finish: Coated Universal Fitment: No Material: Alloy Steel Adjustable: Yes Kit or Single Part: Kit OE Spec or Performance/Custom: OE Spec Quantity: 12Pcs Features: Greasable